Masterkool

Masterkool Fixed Systems


MASTERKOOL HIGH PRESSURE MISTING SYSTEMS

Masterkool's unique high pressure systems provide a very powerful and effective cooling option in those areas where air conditioning is not appropriate or economical.

The systems consist of:

1) High Pressure Pumps

2) Misting Fans

3) Accessories

4) Brass Fittings.

Basically the high pressure pumps pressurise finely filtered tap water to 70 Bar (1,000 psi) and power it through the high pressure hose and nozzles. The result is a very fine mist as small as 5 microns.

The benefits of a Masterkool Misting system are:

  • To reduce surrounding temperature by between 5-10 degrees C
  • Helps control heat stress in animals, increases their wellbeing, and helps increase milk production  
  • Effectively repels mosquitoes, flies, insects and other airborne pests
  • Helps suppress dust
  • Increases oxygen in the air
  • 100% safe to use for everyone
  •   Eco-friendly, no refrigerant gases or CFC's, the surrounding air is absolutely pure
  • Controls odours and neutralises the air leaving it naturally fresh
  •   Energy savings, Masterkool systems operate at 1/10th the cost of  air conditioning

 

1)   MASTERKOOL PUMPS

Masterkool pumps are manufactured at the company plant in Thailand specifically for Masterkool Misting Systems. They are manufactured to a very high standard utilising top quality on consignment parts from 7 different countries. 

There are a number of pumps in the range from the PS10 which can be used for up to a total of 12 nozzles, to the PL80 which can be used for up to 100 nozzles; the size of the pump will depend on the size and nozzle requirements of the system being installed.

 

a)  PUMP - PS10

Misting Capacity: 3 - 12 nozzles

Operating pressure: 70 bar or 1,000 PSI

Inlet water pressure: 1.4 - 5.2 bar or 20 - 75 psi

Electricity: 220 - 240 V

Filter System: 1 Stage External (5 micron)

Waterproof: IP X5

Outer case: Epoxy Coated

Dimensions: 30 x 54 x 30.5 cm

Weight: 26kgs

Automatic Inlet Valve: Yes

Low Water Pressure Cut Off: Yes

Automatic Drain Valve: No

Overheating Protection Valve: Yes

 

b)    PUMP - P120

Misting Capacity: 8 - 32 nozzles

Operating pressure: 70 bar or 1,000 PSI

Inlet water pressure: 1.4 - 5.2 bar or 20 - 75 psi

Electricity: 220 - 240 V

Filter System: 2 Stage Internal (10 - 5 micron)

Waterproof: IP X5

Outer case: Epoxy Coated

Dimensions: 36.5 x 61 x 40 cm

Weight: 37kgs

Automatic Inlet Valve: Yes

Low Water Pressure Cut Off: Yes

Automatic Drain Valve: No

Overheating Protection Valve: Yes

c)     PUMP - PM40

Misting Capacity: 20 - 60 nozzles

Operating pressure: 70 bar or 1,000 PSI

Inlet water pressure: 1.4 - 5.2 bar or 20 - 75 psi

Electricity: 220 - 240 V

Filter System: 2 Stage Internal (10 - 5 Micron)

Waterproof: IP X5

Outer case: Epoxy Coated

Dimensions: 38 x 65.5 x 41.2 cm

Weight: 39kgs

Automatic Inlet Valve: Yes

Low Water Pressure Cut Off: Yes

Automatic Drain Valve: Yes

Overheating Protection Valve: Yes

  

d)    PUMP - PL80

Misting Capacity: 32 - 100 nozzles

Operating pressure: 70 bar or 1,000 PSI

Inlet water pressure: 1.4 - 5.2 bar or 20 - 75 psi

Electricity: 220 - 240 V

Filter System: 2 Stage Internal (10 - 5 Micron)

Waterproof: IP X5

Outer case: Epoxy Coated

Dimensions: 43 x 82 x 43 cm

Weight: 46.7kgs

Automatic Inlet Valve: Yes

Low Water Pressure Cut Off: Yes

Automatic Drain Valve: Yes

Overheating Protection Valve: Yes

 

2)    MASTERKOOL MISTING FANS

 

Masterkool Misting Fans are manufactured at the company plant in Thailand and are different in many ways to standard fans, for example:

  • Masterkool fans are designed specifically for misting applications, standard fans are not
  • Masterkool use special fan motors for open or outdoor areas up to 55°c, normal motors can only be used up to 40°c
  • Masterkool motors can also be used long term in high humid areas, normal motors can’t
  • Masterkool fans include a special motor cover to protect the motor from the rain, standard motors don’t
  • Masterkool fans have a special 2-layer epoxy coating to prevent rust, standard fans have a 1-layer powder coating and will rust
  • Thermal Fuses are included to automatically protect the motor from overheating, standard fans don’t have these

 

There are a number of fans in the Masterkool range all designed to suit the required coverage area or area to be cooled, the number of actual nozzles depends on the size of the fan being used and range from 3 for the smallest to 8 for the largest. All of the fans are available either in standalone or wall mounted versions.

 

FRS20/3 (Stand fan)

Propeller Diameter: 20 Inch

Type: Stand Fan

Misting Capacity: 3 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 30msq

Electricity Power and Current: 220v Single phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 130m3/min

Water Consumption: 12 lh

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 19.7kgs

FRW20/3 (Wall Mounted Fan)

Propeller Diameter: 20 Inch

Type: Wall Mounted Fan

Misting Capacity: 3 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 30msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 130m3/min

Water Consumption: 12 l p/h

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 11.5kgs

 

FRS26/4 (Stand fan)

Propeller Diameter: 26 Inch

Type: Stand Fan

Misting Capacity: 4 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 40msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 195m3/min

Water Consumption: 16 lh

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 20.1kgs

 

FRS26/4 (Stand fan)

Propeller Diameter: 26 Inch

Type: Stand Fan

Misting Capacity: 4 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 50msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 220m3/min

Water Consumption: 16 l/h

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 26.9kgs

 

FRW26/4 (Wall Mounted Fan)

Propeller Diameter: 26 Inch

Type: Wall Mounted Fan

Misting Capacity: 4 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 50msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 220m3/min

Water Consumption: 16 l/h

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 13.9kgs

 

FRS30/8 (Stand Fan)

Propeller Diameter: 30 Inch

Type: Stand Fan

Misting Capacity: 8 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 60msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 302m3/min

Water Consumption: 32 l/h

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 30.8kgs

 

FRW30/8 (Wall Mounted Fan)

Propeller Diameter: 30 Inch

Type: Wall Mounted Fan

Misting Capacity: 8 Nozzles

Mist droplet size: 5 Micron

Area Coverage: 60msq

Electricity Power and Current: 220v Single Phase, 130W, 0.87A

Max Motor Speed: 1420rpm

Maximum Air Volume: 302m3/min

Water Consumption: 32 l/h

Fan Speed: 3 speed

Oscillation Angle: 0* - 90*

Frame: Epoxy Coating

Weight: 17.3kgs

 

 

The pumps are used to power water through the nozzles at 1000psi on all Masterkool Misting Systems with the exception of the portable models such as ISSY, ICE and IKOOL which have their own internal pumping system.

 

Watch our video
How cool can it get?
How much can you save?

Latest News